Product Details:
Voltage | 5 |
Usage/Application | Detection,proximity,motion |
Brand | OLatus |
DC power | 3 - 5 Volts |
Working Current | 15 mA |
Operating Temperature | -20 to 100 Degree C |
Features:
It is a digital sensor, so it can be connected directly to any digital controller board. One pin is for Vcc, second if for Ground and the third pin gives the output signal. The output signal can be connected directly to microcontroller pin.
The sensitivity of the module can be adjusted by turning the potentiometer knob clockwise. By doing this, the range of detection increases. If turned anti-clockwise, the range decreases.
If it detects any obstacle or object, the green LED on board will turn on and simultaneously a signal will be generated in the output pin.
The two LEDs in front of the module are - the black one is an IR led which sends an infrared light, the white one is a photodetector which detects the reflected light. The module is created in such a way that whenever the reflected infrared light is detected by the photodetector, the circuitry gets completed and the signal is generated.
The red LED indicates the power. The module operates on 3-5 Volts of DC power supply.
Product Details:
Brand | OLatus |
Working Voltage | 5 V DC |
Working Current | 15 mA |
Working Frequency | 40 Hz |
Dimension | 45 x 20 x 15mm |
Max Range | 40 cm |
Min Range | 2 cm |
Measuring Angle | 15 Degree |
Product Details:
Brand | OLatus |
Operating Voltage | 5 V |
Working Current | 15 mA |
Operating Temperature | -20 to 100 Degree C |
Being quality-centric firm, we are engaged in presenting a high-class range of Pir Sensor. We assure our clientele the prompt delivery of these products at reasonable prices.
Product Details:
Brand | Olatus |
Power | 5 V |
Operating Temperature | -20 to 100 Degree C |
Product Details:
Brand | OLatus |
Working Voltage | 5 V (DC) |
Mounting Screw Hole | 3 mm |
Product Details:
Minimum Order Quantity | 5 Piece |
Voltage | 3.3V - 5V DC |
Operating Temperature | -20 to 55 Degree C |
Rated Pressure | 25 kPA |
Product Details:
Brand | OLatus |
Dimension Of The Board | 3.2 cm x 1.4 cm |
Working Voltage | 3.3 V - 5 V |
Product Details:
Voltage | 3V - 6V DC |
Power Source | Electric |
Operating Temperature | -20 to 50 Degree C |
Additional Information:
Product Details:
Adjustment | Single Capacitor Per Axis. |
Single Supply Operation | 1.8 v to 3.6 v |
Voltage | 3 V - 6 V DC |
Ultra Low Power | 40uA |
It is Breakout board for the Analog Device''s ADXL345 Tripple axis accelerometer with Voltage regulator onboard. The module is populated with MOSFET based Voltage level conversion circuitry to enable you to interface different type of microcontrollers (3V3 & 5V) . Apart from the above all necessary components like decoupling capacitors , filter capacitors ,Pull up resistors and LED are also populated on board. So out of the box you are ready to go. The ADXL345 is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit two''s complement and is accessible through either a SPI (3- or 4-wire) or I2C digital interface. The ADXL345 is well suited to measures the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Its high resolution (4 mg/LSB) enables measurement of inclination changes less than 1.0°.
Additional Information:
Product Details:
Brand | OLatus |
Acceleration Range | 2 - 4 - 8 - 16 g |
Communication Modes | Standard IC Communications Protocol |
Voltage | 3 V - 5 V |
GY-521 MPU6050 Module 3 Axis analog gyro sensors+ 3 Axis Accelerometer Module, MPU-6050 3 Axis Gyroscope Module For Arduino A 3-axis gyroscope and a 3-axis accelerometer are combined together on the same silicon die with an onboard Digital Motion Processor. Easy to get it fit into your project!
Product Details:
Minimum Order Quantity | 1 Piece |
Brand | OLatus |
Operating Voltage | 2 - 5 v |
PCB Size | 28 x 20 mm |
Responce Time | 60 - 220 ms |
The module is based on a touch-sensing IC (TTP223B) capacitive touch switch module. In the normal state, the module output low, low power consumption; When a finger touches the corresponding position, the module output high, if not touched for 12 seconds, switch to low-power mode. Jog type : the initial state is low , high touch , do not touch is low ( similar touch of a button feature ) Module can be installed in such as surface plastic, glass of non-metallic materials In addition to the thin paper ( non-metallic ) covering the surface of the module , as long as the correct location of the touch , you can make hidden in the walls, desktops and other parts of buttons
Product Details:
Brand | Olatus |
Working voltage | 3.3 V - 5 V |
Humidity measurement range | 20 - 95 % |
Operating Temperature | -20 to 50 Degree C |
Product Details:
Minimum Order Quantity | 1 Piece |
Brand | OLatus |
Input | 3 - 5 V DC |
Size (L x W x H) | 16 x 116 x 3 mm |
Thickness | 2.54 mm |
Product Details:
Minimum Order Quantity | 15 Piece |
Brand | OLatus |
Working Voltage | 5 V (DC) |
Working Current | 15 mA |
Product Details:
Minimum Order Quantity | 1 Piece |
Brand | OLatus |
Rated Voltage | 3.3 V - 5 V |
PCB Dimension | 3.2 cm x 1.4 cm |
Product Details:
Minimum Order Quantity | 1 Piece |
Brand | OLatus |
Wavelength Of Light Source | 760 nm - 1100 nm |
Detect Angle | 60 Degree |
Voltage | 5V |
3.9/5
Rated by 24 Users